james120999
2021-01-15T16:11:58Z
Hello i am new to the PLC world and i am trying to control a traffic light for cars and pedestrian
I am using a START BUTTON I0.1...
I AM NOT USING A STOP BUTTON!!
I want to start off with the GR_CAR ON AND RED_PED OFF
Only when i press the START BUTTON the programm will set
The cycle is :
GR_CAR & RED_PED=15s
YEL_CAR & RED_PED=5s
RED_CAR & GR_PED=4 s
RED_CAR & RED_PED=3s
After that it will GO IN GR_CAR & RED_PED for some period(10 seconds) AND THEN its gonna go to cycle again...
I AM HAVING TROUBLE STARTING THE CYCLE WITH THE START BUTTON BECAUSE IN THE PROGRAMM IM MAKING THE SIMULATION IT STARTS THE CYCLE WHEN I AM PRESSING START IN THE SIMULATION AND NOT WHEN I AM PRESSIN THE START BUTTON(I0.1)!! ALSO I WANT TO SET A TIMMER SO AFTER THE 27 SECOND CYCLE IT WILL GO TO GR_CAR & RED_PED FOR 10 SEC AND ONLY THEN IT SETS TO CYCLE AGAIN...
I WILL APRECIATE IF SOME OF YOU GUYS GIVE ME SOME INTEREST...
Thank you in advance..!!!
host
  •  host
  • 60.57884% (Friendly)
  • Administration
2021-01-27T16:16:16Z
I think the reason you didnt get a response is because your question is not specific enough. There is not really a way to troubleshoot your program via a forum so the question concerning the start pushbutton is just about impossible to address without more information. Concerning the rest of your question, you will need to try to put down some logic and then come with specific questions to problems that arise. I think everyone sees a school project in this and the only way to learn this is to jump in and try things. Good luck and feel free to post specific questions.
Users browsing this topic
    RSLogix500 Introduction
    RSLogix500 Inserting Instructions
    RSLogix500 Opening a File
    RSLogix500 Creating a Project
    RSLogix500 Instruction Comments
    RSLogix500 Rung Comments Page Titles
    RSLogix500 Inserting Branches
    RSLogix500 Program Organization, Part 1 - Overview
    RSLogix500 Program Organization, Part 2 - Examples
    RSLogix500 Using Symbols
    RSLogix500 View Properties
    RSLinx
    RSLogix500 Online Offline
    RSLogix500 Dowloading and Uploading
    RSLogix500 Processor Modes
    RSLogix500 Processor and Cards
    RSLogix500 Introduction to Faults
    RSLogix500 Indirect Addressing
    RSLogix500 Indirect Addressing Faults
    RSLogix500 Handling Faults
    RSLogix500 Forcing I/O
    RSLogix500  Custom Data Monitor
    RSLogix500 I/O Configuration
    RSLogix500 Advanced Diagnostics
    RSLogix500 Instructions OTL OTU, Part 1
    RSLogix500 Instructions OTL OTU, Part 2
    RSLogix500 Instructions OTL OTU, Part 3
    RSLogix500 Instructions, OTE
    RSLogix500 Instructions, XIC XIO
    RSLogix500 Instructions, ADD
    RSLogix500 Instructions, COP
    RSLogix500 Instructions, CPT - Part 2
    RSLogix500 Instructions, CTU CTD - Part 1
    RSLogix500 Instructions, CTU CTD - Part 2
    RSLogix500 Instructions, CTU CTD - Part 3
    RSLogix500 Instructions, CPT - Part 1
    RSLogix500 - Comparison - Part1
    RSLogix500 - Comparison - Part 2
    RSLogix500 Instructions, DIV
    RSLogix500 - FIFO - FFL and FFU - Part 1
    RSLogix500 - FIFO - FFL and FFU - Part 2
    RSLogix500 Instructions, FLL
    RSLogix500 Instructions, JMP and LBL
    RSLogix500 Instructions, Masking and MEQ
    RSLogix500 Instructions, MUL
    RSLogix500 Instructions, MOV
    RSLogix500 Instructions, LIM
    RSLogix500 Instructions, NEG
    RSLogix500 Instructions, OSR
    RSLogix500 Instructions, RTO
    RSLogix500 Instructions, SQO sequencer - Part 1 of 3
    RSLogix500 Instructions, SQO sequencer - Part 2 of 3
    RSLogix500 Instructions, SQO sequencer - Part 3 of 3
    RSLogix500 Instructions, SUB
    RSLogix500 Instructions, TOF
    RSLogix500 Instructions, JSR and RET
    RSLogix500 Shift registers
    RSLogix500 Instructions, SQR
    RSLogix500 Instructions, TON - Part 1
    RSLogix500 Instructions, TON - Part 2
    RSLogix500 Instructions, TON - Part 3
    Introduction to Ladder Logic